Pro-boat JR XR3i Manuel d'utilisateur

3-Channel, 4-Model MemoryFM Computer Racing System4680 JR XR3i manual 7/17/02 12:14 PM Page 1

10Your R-135 receiver is equipped with Battery EliminatorCircuitry (BEC). The receiver gets its power from the model’sNi-Cd battery pack, thus saving

11It’s important to learn the proper sequence for switchingon/off your radio system.Before OperationSwitch on the transmitter, then the receiver.After

12Normal Display When the power switch is turned on, the LCD screen willread as shown below. This screen is referred to as theNormal Display.Note: If

13To enter the System mode, press both the Scroll andChannel keys at the same time while turning on the transmitter power switch. By pressing the Scro

14The XR3i has memory for four models. This feature allowsfor four different models to be operated with the same trans-mitter (additional receivers an

15The Frame Rate function allows you to select one of two transmitter frame rates available: Normal "N" - the default orFast "F".

16The Auxiliary Channel 3 function of the XR3i allows you toselect from two different types of Channel 3 servo travelmovements or to inhibit the Auxil

17The Grip Button C function of the XR3i allows you to selectfrom 3 different functions available. Use the informationbelow to select the correct Grip

INCREASECLEARDECREASESCROLLENTERCHANNEL18Accessing the Grip Button C Function1. Press the Scroll and Channel keys at the same time and hold.2. Turn on

19The Data Reset function allows you to reset all the program-ming in the selected model (1, 2, 3 or 4) to the factory defaultsettings. Before using t

2Model Select . . . . . . . . . . . . . . . . 14Model Name Entry . . . . . . . . . . . 14Frame Rate Select . . . . . . . . . . . . 15Auxiliary Chan

Accessing the Copy Model Data Function1. Press the Scroll and Channel keys at the same time and hold.2. Turn on the transmitter power switch to enter

21To enter the Function mode, it is necessary to first turn onthe transmitter's power switch. Next, press the Scroll keyuntil a beep is heard. Th

22The throttle deadband feature is used to reduce/eliminate thedead throttle area that exists at neutral to the starting point ofthrottle and from neu

23The Exponential feature of the XR3i allows you to alter the response rate of the steering or throttle control aroundneutral without affecting the ma

24The End-Point Adjustment feature of the XR3i allows themaximum travel of both the steering, throttle and AuxiliaryChannel 3 (optional) servos to be

25Accessing The End-Point Adjustment Function1. Turn on the transmitter power switch. 2. Press the Scroll key to enter Function mode.3. Press the Scro

SCROLLENTERCHANNELINCREASECLEARDECREASE26The XR3i offers two different mixing adjustments that allowsfor mixing one channel to another channel. The mi

27The Lap-Timer function of the XR3i allows the recording ofindividual lap times based on a 999 second up-timer. Up to50 laps and times from 3.0 to 99

28The Sub-Trim function of the XR3i is an electronic trimmingfeature that allows the neutral position of the servo on eitherthe steering, throttle or

29The Servo Reversing feature of the XR3i is a very convenientfeature when setting up a new model. The purpose of theservo reversing function is to ch

3Included in this manual are in-depth instructions detailingall the steps and procedures needed to correctly programeach of the XR3i's features.

30The Direct Mode function of the XR3i is accessible throughthe use of the electronic throttle or steering trim levers, aswell as the two electronic g

31The XR3i electronic Steering Trim lever, located just abovethe steering wheel, allows the center position of the servo to be manipulated in either d

32The XR3i's electronic Throttle Trim lever, located to the left of the steering wheel, allows the center position of the servoto be manipulated

INCREASECLEARDECREASE33The Steering Dual-Rate adjustment, located at Grip Lever B,allows the Dual-Rate value (maximum servo travel) to beincreased or

34Brake End-Point AdjustmentThe Brake End-Point Adjustment, located at Grip Lever A,allows the maximum servo travel on the braking side of thethrottle

35When selected, Grip Lever A can be used to access theAuxiliary Channel 3 function of the XR3i for use as a fuelmixture channel.When the LN (linear)

36STEERING THROTTLE AUXTHROTTLE DEADBAND F__________% B__________%EXPONENTIAL __________% F__________% B__________%END-POINT ADJUSTMENT

37STEERING THROTTLE AUXTHROTTLE DEADBAND F__________% B__________%EXPONENTIAL __________% F__________% B__________%END-POINT ADJUSTMENT

38FREQUENCY (MHZ)CHANNEL FREQUENCY (MHZ)CHANNEL FREQUENCY (MHZ)CHANNEL26.995 ...127.045 ...227.095 ...

394. Include detailed information explaining your operation of the system and problem(s) encountered. Provide anitemized list of equipment enclosed an

4Servo Trim AdjustmentSteering 1. With the transmitter power switch on, move the digitalsteering trim lever in the desired position to be adjusted. T

JRPM127©Copyright 2002 Horizon Hobby, Inc.46804 944013 0012714680 JR XR3i manual 7/17/02 12:14 PM Page 40

5Transmitter • 3 channels• FM modulation• Easy-to-read LCD graphics display• 4-model memory• 3-character model name entry• Electronic digital trim lev

6Transmitter XR3iReceiver R-135Servos Z590M x 1 Z270 x 1Accessories BEC switch harness with battery case, servo accessories(for each servo), instructi

7AntennaSteering WheelElectronic DigitalThrottle Trim LeverDot Matrix Multi- Data LCD DisplayThree-Character Name InputDigital VoltageReadingElectroni

85. Before operating your model, make sure your frequency isclear. If someone else is operating on the same frequency,both models will go out of contr

9Charging JackLocated on the left-hand side of the transmitter is the charging jack that accepts only JR wall chargers. Please donot attempt to use an