Instruction Manual
Thank you for choosing the Pro Boat
™
brand. Your satisfaction is our number
one priority. With this in mind, we
have produced this product to be of
the highest quality, performance and
reliability, and at a “value-packed” price.
We hope it provides you with hours of
enjoyment in your next R/C project.
Features
•Revlimiterallowsbriefoperationof
the motor out of the water to protect
the motor and drivetrain components.
•Watercooledforoptimumperformance
without the need for large heat sinks.
•Thesoftstartfeatureslightlylimits
current to increase the life of the
electronic components.
•TheESCalsofeaturesacutoffvoltage
indicator that will stop the motor from
operating if the batteries are reaching
full discharge. To reset, return the
throttle to neutral and bring the boat
to shore at low throttle and recharge
batteries.
•High-powerFETcontrolwith
proportional forward
•High-frequencydesigndeliverssmooth
speed transition
•Pre-wiredwithDean’sbatteryplug,
bullet-style motor connectors and
universalreceiverplugthattJR,
Hitec,AirtronicsZ,FutabaandnewKO
radios
•Pre-programmedforusewithNi-MH
batteries. Can be programmed for
use with Li-Po batteries with PRB3311
ProgrammingModule(soldseparately)
Specications
Operation: Proportional forward
Minimum input voltage: 10V
Maximum input voltage: 21V
BEC voltage: 5.8V
BEC current limit:5A
continuous current maximum:45A
Peak current maximum:55A
Mounting the Speed Control
Note: Be sure all wiring
connections can be reached prior
to mounting.
MounttheProBoatESCinthelocation
speciedbyyourboat’sinstruction
manual. Use the double-sided foam
tape(notincluded)tosecurethespeed
control in position.
Diagram
1.Thepositive(red)andnegative
(brown)wiresmustbereversedto
operate with these radio systems. To
remove the wires from the plug use a
smalljeweler’sscrewdrivertopryup
the plastic tab associated with each
wire. Gently slide the brown wire out
of the plug. Repeat on the red wire
and replace in the opposite positions.
2.InstalltheESCreceiverpluginto
channel 2 or the throttle channel
of the receiver. Install the plug
referencing the wire colors on the
steering servo for proper polarity.
Connecting the Motor Wires
Connect all three wires
to the motor in any
order. If the motor runs
backwards, simply switch
any two wires.
Connecting the Battery
TheProBoatESCcomespre-wiredwith
Dean’s-styleconnectors,compatiblewith
most high-power battery packs.
ProBoatoffersaPRB33133600mAh
Ni-MHpackandaPRB33144200mAh
highcapacityNi-MHbatterywithDean’s
connectorsforusewiththisESC.
1.BesuretheOn/Offswitchisinthe
Offposition.
2. Connect two fully charged 6-cell
Ni-MHsub-Cbatterypackstothe
speedcontrol’sbatteryconnectors.
Waterproof 45A Brushless
Electronic Speed Control (ESC)
Wiring the Receiver
Note:TheProBoatESCuses
the motor battery to supply
power to the receiver. There is
no need for a separate receiver
battery.
•Seeyourradio’sinstructionmanualfor
proper connection. Typically, channel 2
is used to control the throttle.
•Therearethreewiresinvolvedin
the universal receiver connector. It
isdirectlycompatiblewithJR,Hitec,
AirtronicsZ,FutabaandnewKO
systems.
•OlderAirtronicsorKOradiosystems
mustuseamodiedwiringorder.
STEERING
SERVO
MOTOR
CONNECT
ESCTOCH.2
POWER
SWITCH
BATTERY
CONNECTORS
BATTERIES
Commentaires sur ces manuels